Dx8000 client windows 7

DS ControlPoint version 7. It's not recommended to run DS ControlPoint software as a regular monitoring utility on a server or combination component. Reserve a dedicated client computer for this purpose. Do not activate any system lock or screensaver features while running DS ControlPoint software. These features can interfere with certain Digital Sentry processes. Installation requires a Windows administrative user account. Installing the DS ControlPoint software: 1.

Download the DS ControlPoint software from www. Note: Be sure to record the location of the unzipped files. All files should be in the same unzipped folder.

The unzipped folder needs to be local on the PC being installed on not on a USB drive or network share. Article Details Article Number. This means no fast-forwarding or rewinding is necessary to locate the data a user wants to view or export. Another key advantage over tape is decreased maintenance. With no need to replace tapes, DVRs with hard disks can be left unattended for extended periods of time. Since video remains in the digital domain, data is easy to store, transport, and manipulate.

Unlike analog video recordings, digital data does not suffer from a loss in quality when copied or moved from device to device. Because DVRs rely on hard disks instead of tape, data storage is virtually unlimited.

Modern DVRs, such as the DX, allow users to record, play back, and view live video simultaneously. Keeping data digital means video can be easily backed up to a variety of storage media. It also means that alphanumeric information, such as date, time, and transaction statistics, can be synchronously recorded with video.

Refer to the documentation supplied with the optional accessories for instructions on how to install those accessories. DX DX Figure 3. Remove the 12 screws fastening both left and right side plates to the unit. Save the side plates and screws for possible future use. Attach the handles to the rack ears using the four provided x 0. Refer to Figure 5. Using two of the supplied 4 sheet metal Phillips 0. Using the remaining six 4 sheet metal Phillips 0. Refer to Figure 6.

Assemble both sets of front and rear mounting rails using three x 0. Using six of the x 0. Place the unit onto the mounting rails. It should slide in and out of the rack easily. This step may require two persons to lift and slide the unit into place.

Fasten the rack ears to the equipment rack using the four x 0. NOTE: Pelco recommends at least one rack unit 1. Do not block these openings.

Never place the DVR near or over a radiator or heat register. Do not place it in a built-in installation, such as a rack, unless proper ventilation is provided. High-Speed USB 2. Connect the appropriate power cord to the back of the unit and to a power source. Connect the cameras to the BNC connectors. Refer to Table A for video coaxial cable requirements.

Connect power to the cameras. Do not connect these cables directly to the DX All ports are compatible with both RS and RS interface standards. Each port can communicate with and control a variety of PTZ devices. Category 5 UTP is recommended for cable runs greater than feet. Communication parameters are baud rate, parity odd or even , number of parity bits, number of data bits, and number of stop bits.

NOTE: Different types of devices may require alternative cable wiring schemes. Wiring schemes commonly used by Pelco products include straight and rollover types. Refer to the documentation included with your PTZ device to ensure that cables and connectors are wired appropriately. Figure 12 illustrates straight and rollover cable wiring schemes. Each input is programmed to function as either a normally open or normally closed circuit.

Insert the green terminal blocks into the alarm sockets on the back panel of the recorder. Connect one wire from the source device to one of the sensor input terminals 1 through Connect a second wire from the source device to a GND terminal. Each output is programmed to function as either a normally open or normally closed circuit. A signal from a relay output will operate the device connected to the output.

Insert the blue terminal blocks into the relay sockets on the back panel of the recorder. Connect one wire from the device to one of the relay output terminals 1 through NOTE: Relay outputs do not have to correspond numerically to alarm inputs. All sensor input and relay output actions can be linked through programming. Connect a second wire from the relay device to a GND terminal. Once the system has been installed and basic connections have been made, open the front panel of the DVR.

Press the power switch. Wait while the unit starts this may take several minutes. Access levels range from the Administrator group, with the most rights and privileges, to the Restricted group, with the least rights and privileges. The DX comes equipped with two built-in user accounts. What printer driver should I choose? My product does two sets of three beeps.

What does that mean? Does my product use dip switches to change default settings? Can I switch between tractors using ESC codes? Can my product emulate an IBM Proprinter? There is paper loaded on the tractor unit. Why won't my product load paper? My product is not starting printing at the right position on the paper. How can I change the top-of-form setting? How do I create a custom paper size in the Server Properties?

Copy or Print. Select the questions to view the answers Can I print on checks that are 3-inches in length? How can I print barcodes? Error Messages or Lights. Select the questions to view the answers My product beeps five sets of four beeps and will not load paper. Why won't it load paper? I was printing labels and one of the labels peeled off. Now my paper won't feed. Can I remove the platen to get the label out? Paper or Media. Select the questions to view the answers How do I create a custom paper size in the Server Properties?